Go Back   VetteMOD.com > VetteMOD Technical Discussion > Classic Corvettes

Reply
 
Thread Tools
  #581  
Old 09-23-2020, 11:16 AM
BBShark's Avatar
BBShark BBShark is offline
United States | Garage Monkey
 
Join Date: Mar 2008
Location: Right here
Posts: 4,673
My Photos: (340)
Default

The support for the nose of the car looks like a compromise between what is ideal and what would fit the car. Probably all caused by the open hood taking up the space needed to do it properly (as you describe).

The triangulation of the center brace by the rod is really poor. I question the effectiveness of it in the first place. Also, the nose of the car is notched so that the bumper attaches directly to the bracket and does not really support the nose body work. The corner braces do capture the body between the brace and the bumper but how effectively does that support the nose. Support of the nose appears to be accomplished by the headlight brackets that are mounted directly to the bumper. That is a pretty convoluted system for a support.

I don't have a good answer but I was hoping to use a conical front mounted air filter in between the U shaped center brace. Unfortunately, the rod is in that space so I need to come up with something else.
__________________
Reply With Quote
  #582  
Old 09-29-2020, 11:37 PM
rtj's Avatar
rtj rtj is offline
United States | Addict
 
Join Date: Nov 2011
Posts: 2,048
My Photos: (94)
Default

BBshark, there was a guy building a snorkel that went over the rad to an airbox filter on cf. That design might allow you to put a filter on the inlet and tie into your TB. I was kind of amazed he snaked it through there. Probably not hard to tweak/fab.

[Only registered and activated users can see links. Click Here To Register...]


On another note, cf one piece roof. Lightweight isn’t cheap. I posted some of his vids and he mentioned this, but didn’t show it.

[Only registered and activated users can see links. Click Here To Register...]


Fiberglass lower cost version

[Only registered and activated users can see links. Click Here To Register...]

Last edited by rtj; 09-29-2020 at 11:44 PM..
Reply With Quote
  #583  
Old 10-19-2020, 12:27 AM
69427's Avatar
69427 69427 is offline
United States | The Artist formerly known as Turbo84
 
Join Date: Mar 2008
Location: Clinging to my guns and religion in KCMO.
Posts: 2,867
My Photos: (3)
Default Pondering aluminum glasspack mufflers.

Quote:
Originally Posted by 69427 View Post

[Only registered and activated users can see links. Click Here To Register...]
The in-progress picture above is one of the aluminum mufflers I made a few years back, replacing the Dynomax turbos previously on the car. The Dynomax pieces sounded nice and flowed well, but were 16# each. The aluminum replacements ended up at 10# each. They flow well and I'm told they're pretty quiet at WOT. They were a lot of work to fabricate, but I think I can make a couple glasspack syle mufflers pretty easily. They ought to be noticeably lighter, and if the noise level increase is also noticeable, I can just use them at the track, and keep the full size mufflers for street duty.
Reply With Quote
  #584  
Old 10-20-2020, 07:08 PM
BBShark's Avatar
BBShark BBShark is offline
United States | Garage Monkey
 
Join Date: Mar 2008
Location: Right here
Posts: 4,673
My Photos: (340)
Default

Quote:
Originally Posted by rtj View Post
BBshark, there was a guy building a snorkel that went over the rad to an airbox filter on cf. That design might allow you to put a filter on the inlet and tie into your TB. I was kind of amazed he snaked it through there. Probably not hard to tweak/fab.
Haven't made this yet but according to my measurements, this will work.

Reply With Quote
  #585  
Old 10-21-2020, 09:58 PM
rtj's Avatar
rtj rtj is offline
United States | Addict
 
Join Date: Nov 2011
Posts: 2,048
My Photos: (94)
Default

How do you plan to fab it? That guy at cf was making two halves and then bonding them.
Reply With Quote
  #586  
Old 10-23-2020, 03:50 AM
COLE SWEAT's Avatar
COLE SWEAT COLE SWEAT is offline
United States | Member
 
Join Date: May 2013
Posts: 74
My Photos: (0)
Default

Has anyone tried pulling the air from the cowl or windshield wiper space
Reply With Quote
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 04:06 AM.
 


Design by: vBulletin Skins Zone
Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.