Go Back   VetteMOD.com > VetteMOD Workshop > Fabrication Section

Reply
 
Thread Tools
  #1  
Old 09-07-2015, 02:03 AM
69427's Avatar
69427 69427 is offline
United States | The Artist formerly known as Turbo84
 
Join Date: Mar 2008
Location: Clinging to my guns and religion in KCMO.
Posts: 2,572
My Photos: (0)
Default Electric motor advice/sourcing help needed.

Looking for help finding an affordable variable speed motor for a test setup I'd like to build over the winter. I'm trying to do some horsepower (via wattage) measurements of differing engine mechanical fans. I've always distrusted the results I've seen in hot rodding type magazines, as the tests were always done on a static engine dyno (where the fan has to pump a lot of ambient air), whereas in the real world there is varying "wind" speeds entering and exiting the radiator due to the vehicle speed, and this varying wind exit speed should affect the instantaneous angle of attack (for lack of the correct phrase) that the fan blade sees in the moving air. I'd like to vary both the fan RPM (up to about 5000) and the (radiator exit) air speed hitting the fan blades, and measure the electric motor current (and then convert to horsepower) to see what the horsepower requirements are in a somewhat real environment. I don't know at this point what the motor horsepower requirements would need to be, so that's just one of the many unknowns. (I've got another aspect of mechanical fans I'd like to measure, but you'll think I'm crazy if I go into detail on that at the moment, so I'll leave that discussion for later.)

I'm not an electric motor expert, so any helpful suggestions of what might work, and where to get a motor (used and cheaper is preferred) to do this experiment is appreciated.

Thanks.
Reply With Quote
  #2  
Old 09-07-2015, 04:22 AM
Sam Cogley's Avatar
Sam Cogley Sam Cogley is offline
United States | Addict
 
Join Date: Apr 2012
Location: Springfield, MO
Posts: 555
My Photos: (0)
Default

Find a cheap or free treadmill on Craigslist, the type that has a knob on the control panel attached to a potentiometer to vary speed.
Reply With Quote
  #3  
Old 09-07-2015, 10:42 AM
BBShark's Avatar
BBShark BBShark is offline
United States | Garage Monkey
 
Join Date: Mar 2008
Location: Right here
Posts: 4,320
My Photos: (260)
Default

Obviously, a DC motor would be the easiest way to do the conversion at varying speeds. Any idea of the peak HP required (in order to "size" the motor - X watts at 5000rpm)?
__________________
Reply With Quote
  #4  
Old 09-07-2015, 01:18 PM
mrvette's Avatar
mrvette mrvette is offline
United States | Phantom of the Opera
 
Join Date: Mar 2008
Location: NE Florida
Posts: 15,294
My Photos: (3)
Default

All I know is the Dual Spals I have are supposed to spike to near 40 amps on startup, running in direct parallel with each other, no single fan operating setup....and ~25 amps running......my FI computer will turn off the spals when reaching about 40 mph for a few seconds.....a/c running or not......

IMO, any fan at ~45 mph+ is just blocking airflow.....
__________________
"Hell, there are no rules here ... we're trying to accomplish something." Thomas Edison
I have a little list, let ALL of them be MIST......
Reply With Quote
  #5  
Old 09-07-2015, 05:23 PM
69427's Avatar
69427 69427 is offline
United States | The Artist formerly known as Turbo84
 
Join Date: Mar 2008
Location: Clinging to my guns and religion in KCMO.
Posts: 2,572
My Photos: (0)
Default

Quote:
Originally Posted by Sam Cogley View Post
Find a cheap or free treadmill on Craigslist, the type that has a knob on the control panel attached to a potentiometer to vary speed.
I like that! Thanks.
Reply With Quote
  #6  
Old 09-07-2015, 05:30 PM
69427's Avatar
69427 69427 is offline
United States | The Artist formerly known as Turbo84
 
Join Date: Mar 2008
Location: Clinging to my guns and religion in KCMO.
Posts: 2,572
My Photos: (0)
Default

Quote:
Originally Posted by BBShark View Post
Obviously, a DC motor would be the easiest way to do the conversion at varying speeds. Any idea of the peak HP required (in order to "size" the motor - X watts at 5000rpm)?
I don't have a good idea of what the hp requirements are yet, and unfortunately I won't really know until after the test. I've heard some outrageous numbers from some people for the fan drain, but I don't buy it. At the moment I'm just shooting for the most motor I can find at a reasonable price.
Reply With Quote
  #7  
Old 09-07-2015, 05:35 PM
69427's Avatar
69427 69427 is offline
United States | The Artist formerly known as Turbo84
 
Join Date: Mar 2008
Location: Clinging to my guns and religion in KCMO.
Posts: 2,572
My Photos: (0)
Default

Quote:
Originally Posted by mrvette View Post
All I know is the Dual Spals I have are supposed to spike to near 40 amps on startup, running in direct parallel with each other, no single fan operating setup....and ~25 amps running......my FI computer will turn off the spals when reaching about 40 mph for a few seconds.....a/c running or not......

IMO, any fan at ~45 mph+ is just blocking airflow.....
I agree, but it just seems to me that a turning mechanical fan is going to block less air than a non-turning electric fan. (I can't easily prove it at the moment though.)
Reply With Quote
  #8  
Old 09-07-2015, 07:08 PM
mrvette's Avatar
mrvette mrvette is offline
United States | Phantom of the Opera
 
Join Date: Mar 2008
Location: NE Florida
Posts: 15,294
My Photos: (3)
Default

Quote:
Originally Posted by 69427 View Post
Quote:
Originally Posted by mrvette View Post
All I know is the Dual Spals I have are supposed to spike to near 40 amps on startup, running in direct parallel with each other, no single fan operating setup....and ~25 amps running......my FI computer will turn off the spals when reaching about 40 mph for a few seconds.....a/c running or not......

IMO, any fan at ~45 mph+ is just blocking airflow.....
I agree, but it just seems to me that a turning mechanical fan is going to block less air than a non-turning electric fan. (I can't easily prove it at the moment though.)
INteresting point, got NO clue, but I have to ASSume that the fans of any type are being forced to turn at ~45 mph no matter what type they are.....would be curious to know about the mechanical fans and what you are exploring, must be about your racing/class requirements......I"m just an old street racer.....
Reply With Quote
  #9  
Old 09-08-2015, 11:48 AM
BBShark's Avatar
BBShark BBShark is offline
United States | Garage Monkey
 
Join Date: Mar 2008
Location: Right here
Posts: 4,320
My Photos: (260)
Default

Quote:
Originally Posted by 69427 View Post
Quote:
Originally Posted by BBShark View Post
Obviously, a DC motor would be the easiest way to do the conversion at varying speeds. Any idea of the peak HP required (in order to "size" the motor - X watts at 5000rpm)?
I don't have a good idea of what the hp requirements are yet, and unfortunately I won't really know until after the test. I've heard some outrageous numbers from some people for the fan drain, but I don't buy it. At the moment I'm just shooting for the most motor I can find at a reasonable price.
Gene said the fans are @ 25 amps running and I have heard that number before. That's 300 watts. 300 watts @ 5000rpm is a big motor.
Reply With Quote
  #10  
Old 09-16-2015, 08:47 PM
69427's Avatar
69427 69427 is offline
United States | The Artist formerly known as Turbo84
 
Join Date: Mar 2008
Location: Clinging to my guns and religion in KCMO.
Posts: 2,572
My Photos: (0)
Default

Quote:
Originally Posted by BBShark View Post
Quote:
Originally Posted by 69427 View Post
Quote:
Originally Posted by BBShark View Post
Obviously, a DC motor would be the easiest way to do the conversion at varying speeds. Any idea of the peak HP required (in order to "size" the motor - X watts at 5000rpm)?
I don't have a good idea of what the hp requirements are yet, and unfortunately I won't really know until after the test. I've heard some outrageous numbers from some people for the fan drain, but I don't buy it. At the moment I'm just shooting for the most motor I can find at a reasonable price.
Gene said the fans are @ 25 amps running and I have heard that number before. That's 300 watts. 300 watts @ 5000rpm is a big motor.
Okay, this is where I'm a bit foggy. Three hundred watts is less than half a horsepower (.4 hp). I don't have a good feel for what RPM that electric fan is at when consuming that four tenths of a horsepower (and then trying to somehow extrapolate the power draw at 5000 RPM).

Meanwhile, I'm trying a simple experiment until I can get back to my favorite scrap yard where there's usually a treadmill or two thrown in the pile. Dug around in my dad's shop while recently visiting my mom. Found a one horse motor (3450 RPM) with a 5/8" shaft, the same size as the w/p shaft on the Corvette. I tried out a spare fan spacer I had, and it looks like I can bolt up my flex fan to this setup to do an initial test. Here's the motor and spacer:

[Only registered and activated users can see links. Click Here To Register...]

The only question yet is transferring the torque and retaining the spacer on the shaft. The shaft has a keyway, while obviously the fan spacer doesn't. I was kicking around putting a couple set screws into the keyway unless there's better options available (and I'm all ears). Also, I've got a AC breakout cord to allow me to measure the motor current. I don't have a strobe tachometer, so I'm still trying to figure out how to measure the motor/fan speed.
Reply With Quote
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 01:55 PM.
 


Design by: vBulletin Skins Zone
Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.