Go Back   VetteMOD.com > VetteMOD Technical Discussion > Wheels, Tires and Brakes

Reply
 
Thread Tools
  #11  
Old 10-10-2018, 09:31 AM
OZgreen69's Avatar
OZgreen69 OZgreen69 is offline
Australia | Addict
 
Join Date: Apr 2016
Location: Perth Australia
Posts: 158
My Photos: (161)
Default

Here are some pictures of local racing Vettes dual m/c that I find too big or too long and too close to the bonnet. Anyway this is why I like your setup.
[Only registered and activated users can see links. Click Here To Register...][Only registered and activated users can see links. Click Here To Register...]
Reply With Quote
  #12  
Old 10-16-2018, 03:14 AM
vette427sbc's Avatar
vette427sbc vette427sbc is offline
United States | Addict
 
Join Date: Sep 2008
Location: Jersey Shore
Posts: 765
My Photos: (0)
Default

Quote:
Originally Posted by rtj View Post
If you have room you could make it an I-beam in that area.

I bet a lot of guys would pay to send you their pedal box for conversion.
Quote:
Originally Posted by OZgreen69 View Post
I love it!
Strength ? I think that you are good on this one , As you are pushing the pedal you will close the gap, if you understand what I mean? And welded all around... No problem for me, I would do the same. In fact I will do the same as I will copy your mod with no shame at all !!!
So! Don't stop and plenty of pictures please.
Please... copy away!

As far as strength, Im worried about crushing the sleeve... The bearing tolerance is less than .002". If I put 100 lbs of force on the pedal, assuming the masters are hydraulically locked, the pedal should flex (or pivot) about the rear edge of that sleeve (correct me if Im wrong here). If the sleeve is 1" in diameter, half of that is .5. Pedal to the center of the sleeve is 11.25. That gives a ratio of 22.5:1 so at 100 lbs of force on the pedal, there is 2250lbs of force trying to crush this sleeve.
I dont think an I beam would help me here because I already have the center section of the I beam which is what carries this direction of load. I think an H-beam would be more appropriate here, but would require a new pedal design...

Am I overthinking this? Do I need to re-take physics 101? Will real world scenario over-rule theory?
__________________
Chris
AutoWorks Middletown NJ
@autoworksnj
Reply With Quote
  #13  
Old 10-16-2018, 09:08 AM
rtj's Avatar
rtj rtj is offline
United States | Addict
 
Join Date: Nov 2011
Posts: 1,521
My Photos: (45)
Default

Any material you add should help. You could also plate it on either side, using plates with holes drilled for the bearing. If there is room.

For bending beams, I (or as you mentioned, H) are really the best. But they take up space.

Or, You could also static load it and see if the bearing binds.

Last edited by rtj; 10-16-2018 at 09:13 AM..
Reply With Quote
  #14  
Old 10-19-2018, 05:26 AM
OZgreen69's Avatar
OZgreen69 OZgreen69 is offline
Australia | Addict
 
Join Date: Apr 2016
Location: Perth Australia
Posts: 158
My Photos: (161)
Default

Here are some pics of dual M/C one for a Toy and other two for Porsche 911.

[Only registered and activated users can see links. Click Here To Register...][Only registered and activated users can see links. Click Here To Register...][Only registered and activated users can see links. Click Here To Register...]

You can see how they used the sleeve. I don't think that you will have any problem with yours. About the pedal pressure you want to apply, just drive a car and try to notice/remember how hard that you need to push to stop or slow down, you will be surprised like I did driving my car at the track.
Reply With Quote
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 04:23 AM.
 


Design by: vBulletin Skins Zone
Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.