1958 MGA Coupe

tonight i made the wiring harness for the parking lights, i am doing one thing different here and on the left front I am putting a ringed ground on a fender bolt just like on the right side tied into the same wiring ground harness and the parking light. i also will be bringing individual grounds to each of the tail lights, just because over the years i have realized that its a good thing to have solid ground connections at lights

also the parking light wires are soldered, wrapped in electrical tape (like rolling a cigarette, not like a bicycle handle bar), and shrink wrapped. the splices are off set. you do this becasue if you have an errant wire poking through the shrink wrap when its heated and the splices are in the same place you can create a short or other funny wiring problems. wrapping it in tape and then shrink wrap minimizes the poke throughs

this soldered splice is off set but it sure doesnt look like it in the photo, the off set also lets it slide through the tubing easier

20160504_211833_zpsuf1nd4hp.jpg

20160504_212901_zpsgdvkybx2.jpg

20160504_214442_zps3rint9ya.jpg


20160504_214840_zpsvzsgk1nr.jpg

20160504_221839_zpsi3pnusuj.jpg

20160504_223113_zpsqumsxkpm.jpg
 
glued the under dash pad in place. the funny thing about contact adhesive is that you paint both of the mating surfaces and you have no ability for repositioning once its made full contact

so i did this in 4 steps....the first was the middle vertical panel with the big hole and that big hole for the wiring harness was my spot that i aimed to get perfect and then i painted the side to the right , and then the side to the left. lastly i did the heater shelf portion as one unit moving from the back to the front. this made it small enough portions that i didnt screw it up. then when it was in place i cut out the heater shelf hole and brake pedal hole.

20160507_180551_zpsenrkylx6.jpg

those are basically the section lines i wound up using

20160507_180557_zpsthpyrwik.jpg

sorry i cant rotate these for some reason

i let hang over my lower support square tubing and painted it

20160507_183546_zpsr2iylhjz.jpg

20160507_185256_zpsko3kvwj0.jpg

looking at it from the engine bay
20160507_185713_zpsp31qduiz.jpg

and done, use a small roller to make sure everything is pressed flat

20160507_192710_zpszwvapbee.jpg
 
the inner dash pad is a pretty substantial piece, i believe it will work well.


today continue with wiring harness install and put in the headlight dimmer switch. i marked the dimmer switch input with a white dot so for future reference you can see it easily. the dielectric grease also works well to help the grommets slip into place

how much extra wire and i suppose to have down at the dimmer switch end?


20160508_101106_zpsqpwpalbh.jpg

20160508_101112_zps6tqgrzzt.jpg

20160508_110246_zpsdk6xahoi.jpg

20160508_110256_zpsv8r05mcd.jpg

20160508_111556_zpsh52fnukf.jpg
20160508_111606_zpsvbl3zift.jpg


move to the wiper motor bracketry
20160508_111957_zpskvxsqjbs.jpg

20160508_113157_zpsconukpmp.jpg

the end of the hanger right before the hook works well for grabing a stud

20160508_113419_zpscgwhp58g.jpg


20160508_120512_zpsx68vcj9m.jpg
 
oh yeah i agree, i actually see an end....

take out dipper switch wiring harness so it can go through the MC bracket, sand and prep the MC bracket, grease the wiper motor and test it and paint stuff, test voltage regulators


20160509_185513_zpsc3s2euzf.jpg


sand MC bracket and use some metal prep on it.

20160509_190406_zpsvpk5fvdq.jpg

20160509_191509_zpsxtwmcoq0.jpg

test wiper motor with power supply

20160509_192622_zpsd7lmiu5o.jpg

20160509_192646_zpsxlevwehs.jpg

greasse it up with some of my green goop.....i found a thin washer folded in half in the gear area????

20160509_193124_zpsyajzhnuo.jpg


painted wiper motor and tubing

20160509_195321_zpsq2kpgnko.jpg
20160509_195416_zpswssw0jhk.jpg
20160509_200906_zpseg9f6rnk.jpg

20160509_200858_zpsf9mue7rg.jpg

havent we become high tech....power supplies and tablets to read up what you should be looking for

20160509_202510_zps2wd5amw5.jpg

look at that 19v in and 15.4 at the post and all the magic happened at about 16.4 volts


20160509_204825_zpsduj6eemp.jpg


cut out at 9.3 and cut in 12.9...still need to work on the second regulator it is off by 10 volts...
 
tonight match up fasteners for the electrical parts taht get mounted on the fire wall, i carefully put all screws,washers and nuts back on the parts.

wash with warm soapy water

20160510_174320_zpsv19dr9m7.jpg

spray with clear

20160510_180825_zps1gsare2k.jpg

clean terminals stuff with paper and use cardboard to blod off internals and spray with clear

20160510_180833_zps542rlfuo.jpg
 
well my preparation for the grommet install was not as good as i thought.....too many parts left over, and my fingers are exhausted


20160511_211840_zpsqvsvnsfw.jpg

i guess tomorrow i will spend some more time researching what goes where

i have all the cables for tach speedo, choke, starter, heater valvbe, water control taken care of as well as blanking plugs for the brake assembly and the oil pressure line

20160511_211953_zpsguxczmza.jpg

wiper motor ready to go in

20160511_211157_zpsq5fzppvv.jpg

if any one wants to identify the remaining grommets please do.....i do have holes left over for the wiper motor cable, and the water temp capillary tube
 
worked a little more on the harness....all the grommets are in place except for the water capillary , it s looking pretty good up close and in person....

20160512_221115_zpsljapxqop.jpg
 
today do more on the wiring harness, install the wiper motor, hook up some wires, add vin tag and tags to heater....about 4 hrs of work.

added a rubber gasket fron a tire tube to the wiper motor post and used a leather punch to make the hole

20160513_123320_zpsgs7tb0j1.jpg


installing these wiper motors is a PITA...

20160513_133031_zpsnvvs5o5v.jpg





hook up wires and made this long so its easier to replace, my flasher unit doidnt pass testing so i need to buy a new one

20160513_140148_zpsiuvtohcb.jpg

20160513_140208_zpsefzwlsgo.jpg

20160513_150224_zpsqxh1t4jx.jpg
20160513_160634_zpsfqznjkee.jpg


20160513_152315_zpsf8icr4at.jpg

20160513_153138_zpszhy9mqjf.jpg
 
it says thanks

more electrical work...
connecting tool in action

20160514_102308_zps6q8qhfj5.jpg

full compression

20160514_102228_zpsswz6lio6.jpg

adding a ring and additional ground circuit to the ground to go to a body bolt on drivers side
20160514_103156_zpsdgtvdr8g.jpg

test all circuits to make sure everything works

20160514_101815_zps8gwonlns.jpg
20160514_101442_zpseltj2b4d.jpg


20160514_105047_zps2bxzblyj.jpg
20160514_112251_zps6xqnhpav.jpg



20160514_104054_zpssvevz8t5.jpg
 
Last edited:
yes sirreee its close...


worked on those triangular pieces and putting down cork for the frame to body spots

20160515_112852_zpsigke1t2o.jpg

20160515_113544_zpsmgxulhzw.jpg

some black goop for an air tight seal

20160515_115650_zpsmtcswik7.jpg

this spot has to be below the goal post top

20160515_120918_zpsricr3iqy.jpg

i used rivets to make it nice and tight
20160515_121129_zpst9dhfxff.jpg
20160515_122847_zpsn4jqj7gk.jpg

seems like a gasket is a good idea here

20160515_150543_zps5kbklcri.jpg

20160515_155841_zpshgrtvjip.jpg

and lastly put in the fuel sender unit
20160515_144156_zpsl5x9roma.jpg
 
made some progress tonight unclogging my vacuum port on my HS4


20160427_230655_zps0i3ajnio.jpg

i was able to open up the port, this was .030 mig wire

20160520_201558_zpszycjs968.jpg

got the hole open

20160520_203646_zpsmwn5ci9m.jpg

turns out to be about .060

20160520_203714_zpsplocbtdy.jpg

it must have been debris sucked into it i didnt really have to remove any metal to open it up. now what do i put in there to mate up to this

20160520_204436_zpslhjgrpve.jpg

any and all ideas appreciated, what have others done who are using HS4s

thanks bob
 
and done, after thinking about it way too much i just drilled the hole. theres no reason not to take the carbs off if you wanted to.

i used an air vacuum ( for AC systems, do not use a shop vac around gas fumes) to clean out the carb infront of the butter fly

chucked up the bubble flair and did some file work on the profile

20160522_100202_zpsztakolqz.jpg


20160522_103237_zpseij3xjvd.jpg


20160522_105756_zpsxqjldbk7.jpg

just waiting for the rebuilt distributor to hook up the vacum line completely
 
Last edited:
and time to take car of an easy one

20160523_202447_zpslxrdivri.jpg

any body have a good cleaning method for this original bottle?

sand , clean, sand , clean....prime and then paint

20160523_204514_zpsauznqv4a.jpg

1464052523220-1744785128_zpsyujhdcrr.jpg
 

Latest posts

Back
Top